Seal ’n Lock’s Bio-Strip® stripper is a novel blend of environmentally friendly compounds formulated into a non-toxic, highly effective paver sealer remover and paint stripping system. This unique product contains 15% bio-renewable carbon. Its high loading capacity gives it the ability to strip surfaces and remove paver sealer in one application.
This paver sealer remover is an excellent alternative to hazardous low flash point materials such as methylene chloride, NMP, and acetone. All of which are commonly used for stripping applications.
All Seal ‘n Lock products including our paver sealer remover are made of the most environmentally-friendly products available. As a result, they offer excellent weather-ability, UV protection, and help prevent algae and mold. All of our cleaning and sealing products and specialty coatings are VOC compliant in all 50 states and exceed all hardscape product manufacturer’s minimum standards guidelines.
FEATURES AND BENEFITS
Ideal for removing acrylics, enamels, epoxies, lacquers, latex’s, moisture-cured coatings, patio sealer and urethane coatings from most substrates.
Low evaporation rate allows for long stripper on substrate dwell times and lower volume use. This is due to fewer reapplications resulting from solvent evaporation before the coating or paver sealer is removed.
High flash point
High loading capacity makes stripper last longer.
Will not harm aluminum, composites, concrete, metal, steel or wood
Certified environmentally safe
This product contains no carcinogenic or toxic compounds
Contains no peroxides, methylene chloride, NMP or other dangerous chemicals
No ozone depleting chemicals, no hazardous air pollutants (HAPs) and no global warming compounds
Natural Luster® paver sealer from Seal ‘n Lock is a modified acrylic urethane sealer for brick pavers (with an algae and mold inhibitor) that penetrates the pavers to provide a protective barrier with superior joint stabilization (no need for polymeric sand) resulting in a natural luster. Natural Luster® paver coating is user friendly and environmentally safe.
All Seal ‘n Lock products are made of the most environmentally-friendly products available, and offer excellent weather-ability, UV protection, and help prevent algae and mold. All of our cleaning and sealing products and specialty coatings are VOC compliant in all 50 states and exceeds all hardscape product manufacturer’s minimum standards guidelines.
Natural Luster® is designed to be diluted with 1 part water and 1 part sealer with a 2 coat system (flood coat and top coat). Natural Luster® requires mixing and stirring (2 minutes) prior to use.
Natural Luster® paver coating will normally dry in sunny areas within approximately 1 hour. Shaded areas, lower temperatures or high relative humidity will slow the drying process. The surface may be open to foot traffic in 24 hours and to vehicular traffic in 48 hours. To minimize tire marks, vehicles should not make sudden stops or tight turns.
Immediately flush and agitate pump system after sealing with a mixture of 3 gallons water and 8 ounces of pine sol.
Flush out the pump system with 5 gallons of fresh water.
Pour two ounces of Pine Sol into one gallon of water, run through the pump system and leave in the pump until next application.
Always run water through the pump prior to the next application.
Seal ‘n Lock Ultra Wet Look® paver sealer is an advanced sealer with Nano Technology, high solids, low VOC modified acrylic urethane for a wet look enhancement. Seal ‘n Lock Ultra-Wet-Look® paver sealer penetrates the pavers and provides a long-lasting protective barrier with excellent joint stabilization. Ultra-Wet-Look® paver sealer is formulated to seal products made to ASTM C-936 specifications and an absorption rate of 5% or less. Pavers with a higher absorption rate will require an additional application(s) of sealer.
Typically, the application rate will vary from 150 to 200 sq. ft. per gallon, although this rate will vary depending on the texture, absorption rate of the surface and the width of the paver joints.
The free paver sealing class hosted by Surface Logix is this Wednesday, April 5th at 11a.m. Remember if you're coming in a group carpool, and Please NO TRAILERS space is extremely limited. Thank you! Dismiss