Cobble Strip 5 Gallon
$248.00
Cobble Strip is an eco-friendly low odor paint stripper designed to remove various types of coatings. Cobble Strip performs by penetrating and softening the paint film. Cobble Strip will remove most sealers, paints, and concrete stains, both solvent and water based.
Features
Applications
- Commercial grade formulation.
- Easy to rinse.
- Eco friendly.
- Biodegradable.
- Horizontal Brick Pavers
- Natural Stone
- Concrete
Product Directions
Preparations: Before applying Cobble Strip, ensure all areas not being stripped are fully protected. Ensure all surfaces are dry prior to stripping. Water will deactivate the stripping action.
Applications: Stir the product thoroughly before use. Cobble Strip should be applied directly from the container using a roller, or sprayer.
Apply a liberal amount of Cobble Strip to the surface requiring stripping. Work Cobble Strip into grooved areas.
Allow Cobble Strip to stand for a minimum of 30 minutes. Weather conditions, type of coating being removed, and coating thickness will determine how long Cobble Strip must dwell for stripping action to develop.
After softening of paint film begins and film starts to wrinkle, or blister begin to pressure wash the coating off of the substrate. Water will deactivate the stripper. When removing the stripper with water, ensure that rinse water does not contact areas that have not yet been stripped.
Do NOT allow Cobble Strip to dry prior to removing it. When stripping large areas, it is recommended to divide into smaller sections and strip one section at a time rather than attempting to strip the entire project.
READ LABEL THOROUGHLY BEFORE APPLYING PRODUCT
| Weight | 48.50 lbs |
|---|---|
| Dimensions | 13 × 13 × 18 in |
Related Products
Seal ’n Lock’s Bio-Strip® stripper is a novel blend of environmentally friendly compounds formulated into a non-toxic, highly effective paver sealer remover and paint stripping system. This unique product contains 15% bio-renewable carbon. Its high loading capacity gives it the ability to strip surfaces and remove paver sealer in one application.
This paver sealer remover is an excellent alternative to hazardous low flash point materials such as methylene chloride, NMP, and acetone. All of which are commonly used for stripping applications.
All Seal ‘n Lock products including our paver sealer remover are made of the most environmentally-friendly products available. As a result, they offer excellent weather-ability, UV protection, and help prevent algae and mold. All of our cleaning and sealing products and specialty coatings are VOC compliant in all 50 states and exceed all hardscape product manufacturer’s minimum standards guidelines.
FEATURES AND BENEFITS
- Ideal for removing acrylics, enamels, epoxies, lacquers, latex’s, moisture-cured coatings, patio sealer and urethane coatings from most substrates.
- Low evaporation rate allows for long stripper on substrate dwell times and lower volume use. This is due to fewer reapplications resulting from solvent evaporation before the coating or paver sealer is removed.
- High flash point
- High loading capacity makes stripper last longer.
- Will not harm aluminum, composites, concrete, metal, steel or wood
- Certified environmentally safe
- This product contains no carcinogenic or toxic compounds
- Contains no peroxides, methylene chloride, NMP or other dangerous chemicals
- No ozone depleting chemicals, no hazardous air pollutants (HAPs) and no global warming compounds
- No SARA reportable components
- Readily biodegradable
- VOC compliant per EPA, AQMD, and CARB regulations
Cobble Loc is a water-based, two-part product that can be used to protect concrete pavers, natural stone, stamped concrete, and other concrete surfaces. It can be applied on damp surfaces and provides a semi-gloss finish and an enhanced, wet look appearance.
With enhanced joint stability (no need for polymeric sand) and a “wet” look, Seal n Lock’s Super Wet Look® Paver Sealer penetrates the pavers to offer a long-lasting protective barrier.
Super Wet Look® is user-friendly and safe for the environment. Pure urethane has a higher solids content than other sealants, so it wears evenly and lasts longer.
Natural Luster® paver sealer from Seal ‘n Lock is a modified acrylic urethane sealer for brick pavers (with an algae and mold inhibitor) that penetrates the pavers to provide a protective barrier with superior joint stabilization (no need for polymeric sand) resulting in a natural luster. Natural Luster® paver coating is user friendly and environmentally safe.
All Seal ‘n Lock products are made of the most environmentally-friendly products available, and offer excellent weather-ability, UV protection, and help prevent algae and mold. All of our cleaning and sealing products and specialty coatings are VOC compliant in all 50 states and exceeds all hardscape product manufacturer’s minimum standards guidelines.
MIXING
Natural Luster® is designed to be diluted with 1 part water and 1 part sealer with a 2 coat system (flood coat and top coat). Natural Luster® requires mixing and stirring (2 minutes) prior to use.
DRYING TIME
Natural Luster® paver coating will normally dry in sunny areas within approximately 1 hour. Shaded areas, lower temperatures or high relative humidity will slow the drying process. The surface may be open to foot traffic in 24 hours and to vehicular traffic in 48 hours. To minimize tire marks, vehicles should not make sudden stops or tight turns.
CLEANUP
- Immediately flush and agitate pump system after sealing with a mixture of 3 gallons water and 8 ounces of pine sol.
- Flush out the pump system with 5 gallons of fresh water.
- Pour two ounces of Pine Sol into one gallon of water, run through the pump system and leave in the pump until next application.
- Always run water through the pump prior to the next application.
Cobble Impregnator (NS) is a low-VOC, water based, clear breathable sealer for protecting natural stone surfaces. Providing a natural look appearance with no sheen, Cobble Impregnator is ideal for providing protection without changing the surface’s appearance. The breathable formula allows it to be applied in situations where film-forming sealers would not work, including and on surfaces where moisture does not readily dissipate, such as stone installed over a concrete slab.
Each gallon of Cobble Impregnator (NS) will cover approximately 200 square feet per coat; the 5 gallon container of Cobble Impregnator (NS) will cover approximately 1,000 square feet. Coverage will depend on surface porosity, joint width and method of application. Natural Stone may require less material than other substrates.
Over Previously Sealed: Film-forming sealers will need to be stripped prior to application. Cobble Impregnator (NS) may be applied over non film-forming sealers provided the prior application is sufficiently worn away.
Features
- Eco-friendly, super low VOCs
- Protects stone, marble, concrete, and porous tile
- Natural look (not shiny or enhanced)
- Resists stains
- Breathable
Applications
- Protect concrete, marble, pavers, stone, and porous tile against stain, water, and sun damage.
- Roof protection with low or no sheen
- Not used to seal cracks in stucco
Cobble Strip is an eco-friendly low odor paint stripper designed to remove various types of coatings. Cobble Strip performs by penetrating and softening the paint film. Cobble Strip will remove most sealers, paints, and concrete stains, both solvent and water based.
Features
Applications
- Commercial grade formulation.
- Easy to rinse.
- Eco friendly.
- Biodegradable.
- Horizontal Brick Pavers
- Natural Stone
- Concrete
Cobble Loc is a water-based, two-part product that can be used to protect concrete pavers, natural stone, stamped concrete, and other concrete surfaces. It can be applied on damp surfaces and provides a semi-gloss finish and an enhanced, wet look appearance.
With enhanced joint stability (no need for polymeric sand) and a “wet” look, Seal n Lock’s Super Wet Look® Paver Sealer penetrates the pavers to offer a long-lasting protective barrier.
Super Wet Look® is user-friendly and safe for the environment. Pure urethane has a higher solids content than other sealants, so it wears evenly and lasts longer.
THIS ITEM CANNOT BE SHIPPED, IN-STORE PICKUP ONLY.
Cobble Clean is a concentrated eco-friendly blend of biodegradable solvents and detergents formulated for heavy duty degreasing and dirt removal. Use to remove oil, grease stains, chewing gum, and tire marks.
Features
-
Commercial grade cleaning formulation
-
Can be diluted 15 to 1
Applications
-
Remove tire marks
-
Used for commercial property maintenance as well as homeowner cleaning
-
Cleans any walking or driving surface (concrete, stone, paver)
Seal ‘n Lock Ultra Wet Look® paver sealer is an advanced sealer with Nano Technology, high solids, low VOC modified acrylic urethane for a wet look enhancement. Seal ‘n Lock Ultra-Wet-Look® paver sealer penetrates the pavers and provides a long-lasting protective barrier with excellent joint stabilization. Ultra-Wet-Look® paver sealer is formulated to seal products made to ASTM C-936 specifications and an absorption rate of 5% or less. Pavers with a higher absorption rate will require an additional application(s) of sealer.
Typically, the application rate will vary from 150 to 200 sq. ft. per gallon, although this rate will vary depending on the texture, absorption rate of the surface and the width of the paver joints.
ULTRA WET LOOK® BENEFITS:
- Superior Joint Stabilization
- Beautiful Enhancement
- High Solids
- Minimal toxic odor
- Will not harm vegetation
- Provides a Protective Barrier
- No need for polymeric sand
- UV Protection
- VOC compliant in all 50 states
- One day process (No downtime)
- It May be applied to a damp surface
- Inhibits Algae & Mold Growth
- Inhibits weed growth and ant mines
- Hot tire marking resistant
THIS ITEM CANNOT BE SHIPPED, IN-STORE PICKUP ONLY.
This organic cleaner will remove oxide formed stains (i.e. rust from sprinklers) from bare and coated concrete surfaces. When used on interlocking pavers, the surface will not be etched thus protecting the paver’s colors.
Features
- Eliminates ugly brown stains formed by rust or fertilizers on concrete surfaces
- Will not etch surface of pavers in order to protect richness of pavers’ colors
Applications
- Removes sprinkler and fertilizer rust
- Use in spray bottle to remove rusty stains from sprinklers on walls
- Paver and concrete cleaner
Reviews
There are no reviews yet.