UltraWet 5 Gallon
$224.00
Seal ‘n Lock Ultra Wet Look® paver sealer is an advanced sealer with Nano Technology, high solids, low VOC modified acrylic urethane for a wet look enhancement. Seal ‘n Lock Ultra-Wet-Look® paver sealer penetrates the pavers and provides a long-lasting protective barrier with excellent joint stabilization. Ultra-Wet-Look® paver sealer is formulated to seal products made to ASTM C-936 specifications and an absorption rate of 5% or less. Pavers with a higher absorption rate will require an additional application(s) of sealer.
Typically, the application rate will vary from 150 to 200 sq. ft. per gallon, although this rate will vary depending on the texture, absorption rate of the surface and the width of the paver joints.
ULTRA WET LOOK® BENEFITS:
- Superior Joint Stabilization
- Beautiful Enhancement
- High Solids
- Minimal toxic odor
- Will not harm vegetation
- Provides a Protective Barrier
- No need for polymeric sand
- UV Protection
- VOC compliant in all 50 states
- One day process (No downtime)
- It May be applied to a damp surface
- Inhibits Algae & Mold Growth
- Inhibits weed growth and ant mines
- Hot tire marking resistant
Ultra Wet Look® paver sealer is user friendly and environmentally safe. The high solids content wears evenly and lasts longer than solvent based paver sealers.
All Seal ‘n Lock products are made of the most environmentally-friendly products available, and offer excellent weatherability, UV protection, and help prevent algae and mold. All of our cleaning and sealing products and specialty coatings are VOC compliant in all 50 states and exceeds all hardscape product manufacturer’s minimum standards guidelines.
MIXING
Ultra Wet Look® paver sealer is designed to be diluted with 1 part water to 1 part sealer. Ultra Wet Look® paver sealer requires mixing (2 minutes) prior to use. We recommend 2 coats. Pavers with high absorption rate will require additional top coats of sealer to provide a protective barrier and desired enhancement. Ultra Wet Look® is not intended for submerged surfaces.
DRYING TIME
Ultra Wet Look® paver sealer will normally dry in sunny areas within approximately 1 hour. Shaded areas, lower temperatures or high relative humidity will slow the drying process. The surface may be open to foot traffic in 24 hours and to vehicular traffic in 48 hours. To minimize tire marks, vehicles should not make sudden stops or tight turns.
CLEANUP
- Immediately flush and agitate pump system after sealing with a mixture of 3 gallons water and 8 ounces of Pine-Sol
- Flush out the pump system with 5 gallons of fresh water
- Pour two ounces of Pine Sol into one gallon of water, run through the pump system and leave in the pump until next application.
- Always run fresh water through the pump prior to the next application
| Weight | 48.50 lbs |
|---|---|
| Dimensions | 13 × 13 × 18 in |
Related Products
With enhanced joint stability (no need for polymeric sand) and a “wet” look, Seal n Lock’s Super Wet Look® Paver Sealer penetrates the pavers to offer a long-lasting protective barrier.
Super Wet Look® is user-friendly and safe for the environment. Pure urethane has a higher solids content than other sealants, so it wears evenly and lasts longer.
Cobble Impregnator (NS) is a low-VOC, water based, clear breathable sealer for protecting natural stone surfaces. Providing a natural look appearance with no sheen, Cobble Impregnator is ideal for providing protection without changing the surface’s appearance. The breathable formula allows it to be applied in situations where film-forming sealers would not work, including and on surfaces where moisture does not readily dissipate, such as stone installed over a concrete slab.
Each gallon of Cobble Impregnator (NS) will cover approximately 200 square feet per coat; the 5 gallon container of Cobble Impregnator (NS) will cover approximately 1,000 square feet. Coverage will depend on surface porosity, joint width and method of application. Natural Stone may require less material than other substrates.
Over Previously Sealed: Film-forming sealers will need to be stripped prior to application. Cobble Impregnator (NS) may be applied over non film-forming sealers provided the prior application is sufficiently worn away.
Features
- Eco-friendly, super low VOCs
- Protects stone, marble, concrete, and porous tile
- Natural look (not shiny or enhanced)
- Resists stains
- Breathable
Applications
- Protect concrete, marble, pavers, stone, and porous tile against stain, water, and sun damage.
- Roof protection with low or no sheen
- Not used to seal cracks in stucco
Natural Luster® paver sealer from Seal ‘n Lock is a modified acrylic urethane sealer for brick pavers (with an algae and mold inhibitor) that penetrates the pavers to provide a protective barrier with superior joint stabilization (no need for polymeric sand) resulting in a natural luster. Natural Luster® paver coating is user friendly and environmentally safe.
All Seal ‘n Lock products are made of the most environmentally-friendly products available, and offer excellent weather-ability, UV protection, and help prevent algae and mold. All of our cleaning and sealing products and specialty coatings are VOC compliant in all 50 states and exceeds all hardscape product manufacturer’s minimum standards guidelines.
MIXING
Natural Luster® is designed to be diluted with 1 part water and 1 part sealer with a 2 coat system (flood coat and top coat). Natural Luster® requires mixing and stirring (2 minutes) prior to use.
DRYING TIME
Natural Luster® paver coating will normally dry in sunny areas within approximately 1 hour. Shaded areas, lower temperatures or high relative humidity will slow the drying process. The surface may be open to foot traffic in 24 hours and to vehicular traffic in 48 hours. To minimize tire marks, vehicles should not make sudden stops or tight turns.
CLEANUP
- Immediately flush and agitate pump system after sealing with a mixture of 3 gallons water and 8 ounces of pine sol.
- Flush out the pump system with 5 gallons of fresh water.
- Pour two ounces of Pine Sol into one gallon of water, run through the pump system and leave in the pump until next application.
- Always run water through the pump prior to the next application.
Cobble Strip is an eco-friendly low odor paint stripper designed to remove various types of coatings. Cobble Strip performs by penetrating and softening the paint film. Cobble Strip will remove most sealers, paints, and concrete stains, both solvent and water based.
Features
Applications
- Commercial grade formulation.
- Easy to rinse.
- Eco friendly.
- Biodegradable.
- Horizontal Brick Pavers
- Natural Stone
- Concrete
Cobble Loc is a water-based, two-part product that can be used to protect concrete pavers, natural stone, stamped concrete, and other concrete surfaces. It can be applied on damp surfaces and provides a semi-gloss finish and an enhanced, wet look appearance.
With enhanced joint stability (no need for polymeric sand) and a “wet” look, Seal n Lock’s Super Wet Look® Paver Sealer penetrates the pavers to offer a long-lasting protective barrier.
Super Wet Look® is user-friendly and safe for the environment. Pure urethane has a higher solids content than other sealants, so it wears evenly and lasts longer.
Cobble Loc is a water-based, two-part product that can be used to protect concrete pavers, natural stone, stamped concrete, and other concrete surfaces. It can be applied on damp surfaces and provides a semi-gloss finish and an enhanced, wet look appearance.
Cobble Strip is an eco-friendly low odor paint stripper designed to remove various types of coatings. Cobble Strip performs by penetrating and softening the paint film. Cobble Strip will remove most sealers, paints, and concrete stains, both solvent and water based.
Features
Applications
- Commercial grade formulation.
- Easy to rinse.
- Eco friendly.
- Biodegradable.
- Horizontal Brick Pavers
- Natural Stone
- Concrete
Seal ’n Lock’s Bio-Strip® stripper is a novel blend of environmentally friendly compounds formulated into a non-toxic, highly effective paver sealer remover and paint stripping system. This unique product contains 15% bio-renewable carbon. Its high loading capacity gives it the ability to strip surfaces and remove paver sealer in one application.
This paver sealer remover is an excellent alternative to hazardous low flash point materials such as methylene chloride, NMP, and acetone. All of which are commonly used for stripping applications.
All Seal ‘n Lock products including our paver sealer remover are made of the most environmentally-friendly products available. As a result, they offer excellent weather-ability, UV protection, and help prevent algae and mold. All of our cleaning and sealing products and specialty coatings are VOC compliant in all 50 states and exceed all hardscape product manufacturer’s minimum standards guidelines.
FEATURES AND BENEFITS
- Ideal for removing acrylics, enamels, epoxies, lacquers, latex’s, moisture-cured coatings, patio sealer and urethane coatings from most substrates.
- Low evaporation rate allows for long stripper on substrate dwell times and lower volume use. This is due to fewer reapplications resulting from solvent evaporation before the coating or paver sealer is removed.
- High flash point
- High loading capacity makes stripper last longer.
- Will not harm aluminum, composites, concrete, metal, steel or wood
- Certified environmentally safe
- This product contains no carcinogenic or toxic compounds
- Contains no peroxides, methylene chloride, NMP or other dangerous chemicals
- No ozone depleting chemicals, no hazardous air pollutants (HAPs) and no global warming compounds
- No SARA reportable components
- Readily biodegradable
- VOC compliant per EPA, AQMD, and CARB regulations
Reviews
There are no reviews yet.